Time you cannot invoice
Going through every room — height, ceiling type, occupancy, ventilation and obstructions — to derive coverage area and spacing: hours of spreadsheet work for a single floor.
You are the designer. FIREAXIS is the tool installers, electricians, architects and design offices use to lay out their fire detection, have the coverage checked, and produce a calculation note that points to the applicable clauses — based on the Belgian standards NBN S 21-100-1:2025 and NBN S 21-112-3:2025.
Placing detectors is not a matter of symbols: it is a coverage calculation under normative constraints. In practice you do it by hand, under deadline pressure. That is exactly what the platform takes over — without ever deciding for you.
Going through every room — height, ceiling type, occupancy, ventilation and obstructions — to derive coverage area and spacing: hours of spreadsheet work for a single floor.
A detector too close to a wall, a beam crossing the ceiling, a narrow room, a sloped ceiling: in each case the real coverage is smaller than the drawing suggests.
At commissioning, every choice has to be explainable. Without a calculation note tied to the drawing, the conversation with the inspection body turns into rework on site.
From concept design to commissioning, on new buildings and existing installations alike. The file stays yours : the platform signs nothing, it makes every choice verifiable.
You import the drawing, outline the rooms, and place detectors, manual call points and sounders. The platform keeps up : zone division, detection type allowed per room, coverage area and spacing recalculated at every move.
You get : the laid-out drawing + the take-offEvery position is tied to the clause that governs it : monitored area, critical distance, height, slope, sound levels used. That is what you defend at commissioning — and it is generated instead of written.
You get : the calculation note, room by roomAlready have a layout ? Transfer it and run the check : rooms wrongly exempted, zones outside the allowed limits, insufficient coverage, oversized equipment. Every deviation is named and shown at the exact place it occurs.
You get : the list of deviations, clickable on the drawingSurvey the installed system, test it against the standard in force, and extract what is missing : what to move, to add, to remove. Prioritised, and ready to price.
You get : the gap against the standard + the remedial take-offThe one place where Fire Axis steps in alongside the tool : getting started with the platform, method for finding your way through the standard, classic pitfalls, design trade-offs. On your real projects, with your drawings. No normative document is handed out or projected : everyone works from their own copy of the standards they apply.
Format : working sessionYou import the drawing. You describe the rooms. You place the devices where the site allows — and the engine measures what each one really covers, then hands you back the drawing and its calculation note.
You place, the engine measures. A badly placed device leaves a gap : its radius turns red, and goes back to green as soon as it covers.
A shaft is judged in three dimensions. The sampling column runs down on the aspirator side, and the aspirator stays outside the duct — where it can be reached.
Ceiling shape changes the rule. Under an apex roof the row follows the ridge ; on a single pitch or a sawtooth roof, it sits differently.
The threshold is not the same everywhere. 65 dB(A) in a hall, 75 dB(A) at a bedhead : 68 dB(A) passes in one and fails in the other.
Video detection does not cover an area : it sees. Its range is a line of sight, and every obstruction takes away what it hides — lighting then becomes a detection requirement.
You import the drawing (DXF or PDF) and calibrate it against a printed dimension. It is the one step everything else depends on : a wrong scale makes every area wrong.
Level of surveillance, exempted rooms, occupancy and height of each room, detection type suited to the risk. You decide ; the platform derives the applicable limits, Table by Table.
You place the devices where the site allows. The coverage radius colours live — green, amber, red — and one button tests the whole floor against the standard, clause by clause.
Laid-out drawing, take-off, loop routing and calculation note : exportable as PNG, PDF and DXF. It is your file and your signature — every figure carries the reference of the clause behind it.
See early what detection imposes on ceilings, suspended ceilings and builder's openings — before the services package discovers them.
A reproducible, traceable coverage calculation that you run yourself and can put in front of the inspection body.
A reliable take-off to price accurately, a loop route that saves cable, and positions that do not force rework on site.
A clear picture of what is installed and a route to compliance you can budget for.
On the 2025 editions, in force since 17 July 2025. They separated what used to be combined : the NBN S 21-100 series now covers only automatic detection — zones, detector types, coverage areas and spacings, manual call points — while the NBN S 21-112 series governs the alarm, including NBN S 21-112-3 for sounders and the levels to be reached. The platform implements NBN S 21-100-1:2025 and NBN S 21-112-3:2025, and the edition used is printed on every document it produces : a calculation run on an outdated version is worthless, and that must be visible. Every verdict cites the clause it rests on : you can check it, and challenge it. Requirements specific to your project — regional regulations, fire service instructions, insurer's requirements — remain your judgement : the platform does not know them.
No. FIREAXIS handles addressable systems only, and it is better to know that before creating an account than after. This is not an arbitrary limit : everything the platform does rests on a device being IDENTIFIABLE one by one — the loop and its isolators, the number of components per circuit, the schedule that goes out for quotation, the check that names the room at fault. On a conventional system the unit is no longer the device but the wired zone ; the rules for wiring, zoning and verification are not the same, and applying them to a conventional drawing would produce a wrong file with the appearance of a correct one.
DXF preferably : the geometry is already structured there. A PDF or an image works just as well, provided the scale is calibrated against a printed dimension — and that is the step not to rush : a title block stating the wrong scale is the most common defect, and it makes every area wrong, and therefore the whole detector count.
Neither, and that is deliberate. You are the designer : the platform places nothing on your behalf, it reads what you have placed and tests it against the standard. The file carries your signature, not ours. And regulatory validation remains the responsibility of the approved body that commissions the installation : the tool prepares commissioning by making every choice verifiable, it does not pronounce it.
Your projects live in your own space, separate from every other user's. Nobody else reaches them — not even a peer working on the same building, for the same client. One single exception, tightly bounded : to troubleshoot for you, Fire Axis can open your file for two hours at most. That access is recorded in your account — date and reason — and a banner shows it for as long as it lasts. A project becomes visible to someone only if you invite them, and you withdraw that whenever you want.
Everything exports at any time : the file as PDF, the project as a single file you take with you. And if you stop your subscription, your earlier projects remain viewable and exportable : they are yours, you made them.
You, and the people you invite onto a specific project — for that project only. The guest creates their own account ; they inherit none of your other files. On the handover date you set, guest access expires on its own.
Fire Axis resells nothing, cross-references nothing and exploits none of your drawings. The only data that leaves the platform is what you export yourself.
No : that is precisely the point. Every tool explains what it does, every non-compliance is written in plain language before being tied to its clause, and one click shows it at the exact place on the drawing. You do, however, need to know your building — the heights, the uses, the doors, the beams : no drawing states those, and the platform asks you for them.
It is in early access. It is opening gradually to installers, electricians, design offices and architects who use it on their real projects and steer its development — their feedback decides what gets built next. Write to us to be in the next wave.
Every account is opened by hand : you tell us who you are, we open it. Reply within two working days.
A design question, a rule, a deadline. Reply within two working days.
No approval, no certification. FIREAXIS is neither an inspection body nor a certification body. It issues no certificate of conformity. Regulatory validation remains the responsibility of the approved body that commissions the installation, and responsibility for the design remains with the designer who signs the file.
It does not replace the standard. The documents produced refer to the applicable clauses ; they reproduce neither the text, nor the tables, nor the figures — these are protected by NBN's copyright. Users are expected to hold their own copy of the standards they apply.
Editions implemented : NBN S 21-100-1:2025 and NBN S 21-112-3:2025, in force since 17 July 2025. Any change to the texts is carried through and dated ; the edition used appears on every export.
What the calculation is. A design estimate, run on the data you enter — scale, heights, uses, partitions, equipment. It is worth what that data is worth. Sound levels in particular remain an estimate : the proof is still on-site measurement.